Rock Hard Rear Bumper
Jeep Wrangler TJ, YJ and CJ's
Patent Pending
Rock Hard Jeep Rear Bumper/Tire-Carriers are made out of
3/16" x 2" x 4" thick tubing with ends that are boxed in. They have 2 sets of holes which mount to your Jeep frame in a standard position or can be raised 1" to increase departure angle and/or compensate for body lift. This bumper also comes with
(2)-5/8" x 2-1/2" CNC D-Ring shackle mount with tabs that are welded on front, go through bumper and then welded on the backside too. A CB antenna mount and horizontal Hi-Lift Jack mount with padlock provision comes standard. The swing out tire carrier will hold up to a 38" tire. All needed hardware is furnished for installation.
Rock Hard Rear Bumper/Tire-Carrier Only
Unpainted Bare Metal
Part #
RH2001
$684.95
Powder Coated Black
RH2001-C
$729.95
Features
|
 |
 |
Photos of what the Rock Hard Jeep Rear Bumper/Tire-Carrier (RH2001-C) looks like mounted on a Jeep TJ Wrangler complete with over sized spare tire and Hi-Lift Jack. |
 |
 |
The Rock Hard Jeep bumper tire carrier swings on 1 1/4" shaft, 2 3/4" hub with upper and lower sealed tapered roller bearings.
Zerk fittings allow you to fill the hinge with grease.
Choose from 3 bolt patterns: 4.5" x 5, 5.5" x 5, or 5.5" x 6. Also, notice the A-Frame swing stop built into the bumper. |
 |
 |
Easy open latch. Just lift lever to open
self-latching design. To close, simply push it shut.
Also included is a double safety latch with hard plastic rest and rubber stop for a rattle free operation. |
 |
 |
Spring loaded auto-locking pin system. Tire carrier locks in the open position so it will not swing back at you.
To close, just lift tee handle on the pin and let it swing shut. |
 |
 |
Jeep Tail gate isolator bar provides a tight rattle free fit. |
| |
 |
The Rock Hard Jeep Bumper has an Integrated class 2 trailer hitch comes complete with safety change mounts. |
| |
 |
The Rock Hard Jeep Frame Kit is recommended with tires larger than 33" or with Rock Rack or Can Mounts.
Jeep TJ Kit shown with 2 of 3 possible bolts installed, requires drilling 3rd hole. |
|
|
Optional right and left tank mounts works with NATO or USA cans. Rattle Free J - Bolt Mounting for Cans and Provisions for Padlocks are provided.
U - Bolt Mounting to the swing out tire carrier allows for easy installation. |
 |
 |
This is what the Rock Hard gas tank mounts look like with NATO or USA cans on them. |
| |
 |
Left gas tank mount has an additional CB Antenna Tab. |
 |
 |
The optional Rock Hard Rock Rack
(RH2004) has an inside measurements or 5 1/4" deep, 18 1/4" wide and 38 1/2" long. |
| |
 |
This photo shows the Rock Hard Rock Bumper from the back side complete with Rock Rack and Tank Mounts. |
| |
 |
In order to install an optional 3rd brake light (RH2002TL), the center hole on your wheel must be 2 - 1/2" or larger. Installation only requires you to splice the light onto your factory light wiring.
Longer wires, screws and required connectors are Included. |
 |
 |
This license plate relocation (RH4007) bracket will allow you to relocate your rear license plate to the center of your spare tire. Quick release thumb screw allows for easy removal on the trail. An optional 3rd brake/license plate light (RH4006) can also be added. |
| |
|
|
